Maas Logistics Dispatch · Drivers & Hiring
CDL Pre-Trip Inspection Checklist: A Step-by-Step Walkaround for Dry Van and Reefer Drivers, and Why Carriers Care About It When They Hire
· By Maas Logistics Dispatch
Every CDL-A driver learns a pre-trip inspection to pass the skills test. The drivers who last in this business keep doing a real one every day after that. This CDL pre-trip inspection checklist is written for tractor-trailer drivers hauling dry van and reefer freight: what to check, in what order, what the federal rules actually require, and why the carriers worth driving for pay attention to how you do it.
It is written by Maas Logistics LLC, an asset-based dry van and reefer carrier in Melissa, Texas, on the north side of Dallas–Fort Worth. We have run full truckload freight across the lower 48 states since 2018 with our own trucks and our own drivers, and we never re-broker a load. We are not a CDL school and this is not legal advice. Your carrier's procedures, the truck's manufacturer manual and your state's CDL handbook come first. Use this as a practical checklist and a reminder of why the walkaround matters.
Why the pre-trip inspection matters more than ever
Roadside enforcement is busy right now. On Nov. 6, the Commercial Vehicle Safety Alliance released its 2026 Brake Safety Week results: inspectors in 51 jurisdictions ran 15,528 brake inspections and placed 2,369 vehicles out of service, about 15.3%, or roughly one truck in seven. Brake hoses and tubing alone produced 600 out-of-service violations. We covered those numbers in our Nov. 8 trucking news roundup.
At the same time, enforcement of driver qualification rules is tight, and FreightWaves CEO Craig Fuller told an industry conference this month that he expects the crackdown to stay, because the largest carriers want tighter standards. We wrote that up in today's trucking news roundup. Put those together and the message for drivers is simple: a careful driver with clean inspections is exactly who good carriers want to hire.
A thorough pre-trip protects three things at once:
- You. A defect you catch in the yard is a repair. A defect a roadside inspector catches is a violation tied to your name and your carrier's record. A defect nobody catches can be a crash.
- Your clock. An out-of-service order or a breakdown on the shoulder eats hours you will never get back. Ten minutes at the start of the day is cheaper.
- Your carrier's record. Inspection results feed the carrier's public safety data. Carriers that keep a Satisfactory safety rating do it one inspection at a time. Maas Logistics is USDOT 3179194 with a Satisfactory safety rating; you can read more on our safety page.
What the federal rules actually require
Three short sections of the Federal Motor Carrier Safety Regulations cover most of what a driver needs to know.
49 CFR 392.7: be satisfied before you drive
Under 49 CFR 392.7, a commercial motor vehicle may not be driven unless the driver is satisfied that these parts and accessories are in good working order:
- Service brakes, including trailer brake connections
- Parking (hand) brake
- Steering mechanism
- Lighting devices and reflectors
- Tires
- Horn
- Windshield wiper or wipers
- Rear-vision mirror or mirrors
- Coupling devices
- Wheels and rims
- Emergency equipment
That list is the backbone of every good pre-trip. If you remember nothing else, remember those eleven items.
49 CFR 396.13: review the last inspection report
Before driving, 49 CFR 396.13 says the driver must be satisfied the vehicle is in safe operating condition, review the last driver vehicle inspection report (DVIR) when one is required, and sign it to acknowledge the review and that required repairs were certified. Those reports can be electronic.
49 CFR 396.11: the DVIR at the end of the day
Under 49 CFR 396.11, drivers prepare a written report at the end of each day's work on each vehicle they operated, covering the same parts and accessories listed above. If no defect or deficiency is discovered by or reported to the driver, the driver is not required to prepare a report. If there is a defect that would affect safe operation, the carrier must repair it, or certify that repair is unnecessary, before the vehicle runs again. Carriers keep those reports for three months.
The practical point: your pre-trip and your post-trip are two halves of the same job. The post-trip tells the shop what to fix. The pre-trip confirms it was fixed.
The CDL pre-trip inspection checklist, step by step
Every carrier and every CDL school teaches a slightly different order. What matters is that you do it the same way every time so nothing gets skipped. Here is a practical order for a tractor pulling a 53-foot dry van or reefer.
Step 1: Approach the truck
Before you touch anything, look at the whole unit as you walk up.
- Is the truck leaning or sitting low on one side?
- Any fresh puddles of fuel, oil, coolant or other fluid under the tractor or trailer?
- Any obvious body damage, hanging parts or loose items since the last time you saw it?
- Review the last DVIR and any repair notes before you start.
Step 2: Engine compartment
With the engine off and the hood tilted (follow your truck's procedure):
- Oil level on the dipstick and coolant level in the reservoir
- Power steering fluid, if your tractor has a separate reservoir
- Belts for cracks, fraying and proper tension
- Hoses for leaks, cracks, bulges and secure clamps
- Air compressor and its mounting, if visible
- Wiring for chafing or loose connections
- Steering box, steering linkage and tie rod ends: nothing loose, bent or missing
Step 3: Start up and in-cab checks
Close the hood, make sure the parking brakes are set, then start the engine.
- Gauges: oil pressure comes up, coolant temperature, voltage, and air pressure building
- Warning lights: check that the dash warning lights and buzzers work and then clear
- Steering wheel free play: excessive play is a defect
- Horn(s), windshield wipers and washer fluid, heater and defroster
- Mirrors clean, adjusted and secure; windshield free of cracks that block your view
- Seat belt works
- Emergency equipment: fire extinguisher charged and secured, three reflective warning triangles, and spare fuses if your truck needs them
- ELD working and logged in. At Maas, our trucks run Samsara ELDs; our hours of service rules guide explains what your day looks like under the clock.
Step 4: The air brake check
This is the part of the pre-trip most drivers remember from the CDL test, and the part that catches the most problems. The figures below are the standard ones from the CDL manual for a combination vehicle with a dual air system. Check your state's CDL handbook and your truck's manual.
- Air pressure build-up. With the engine at operating RPM, pressure should build from 85 to 100 psi within about 45 seconds on a dual air system.
- Governor cut-out. The compressor should stop building (cut out) at the pressure your truck's manufacturer specifies (the CDL manual uses about 125 psi as the typical figure) and cut back in as pressure drops.
- Static leak test. Fully charged, engine off, parking brakes released: the system should lose less than 3 psi in one minute for a combination vehicle.
- Applied leak test. Hold firm pressure on the brake pedal: after the initial drop, the loss should be no more than 4 psi in one minute for a combination vehicle.
- Low air warning. Fan the brakes down. The low-pressure warning light and buzzer must come on before pressure falls below 60 psi.
- Spring brakes. Keep fanning. The tractor protection valve and parking brake valves should pop out (spring brakes apply) somewhere between 20 and 45 psi.
- Parking brake and service brake tests. With the parking brakes set, gently try to pull forward to make sure they hold. Then roll forward slowly and apply the service brake to make sure the truck stops straight with no pulling.
If any of those numbers are off, do not roll. Call dispatch and the shop. Brakes were the single biggest reason trucks were placed out of service during Brake Safety Week, and they are the easiest problem to find while you are still in the yard.
Step 5: Lights and reflectors
Turn on the headlights and the four-way flashers, then walk the unit.
- Headlights (high and low), clearance and identification lights, marker lights
- Turn signals and four-ways front, side and rear
- Brake lights (a helper makes this easy)
- Reflectors and the red-and-white conspicuity tape on the trailer sides and rear: clean, present and not peeling away
Step 6: Tires, wheels and rims
Check every tire, including the inside duals.
- Tread depth: under 49 CFR 393.75, steer tires need at least 4/32 of an inch in a major tread groove, and all other tires at least 2/32.
- No exposed ply or belt, no tread or sidewall separation, no cuts down to the cord, no bulges
- Not flat and no audible leak; check pressure with a gauge, not by thumping the tire
- Nothing stuck between the duals
- Valve stems and caps present
- Lug nuts all present and tight; look for rust trails or shiny metal around the nuts, which can mean a loose wheel
- Rims not cracked or bent; hub oil seals and axle seals not leaking
Step 7: Brakes and suspension at each axle
At each wheel position, look without crawling under the truck unless your carrier allows it and the truck is safely secured.
- Brake chambers secure, no air leaks, no cracks
- Slack adjusters: not broken or loose; pushrod travel within limits (your carrier and the CDL manual will show you how to check it)
- Brake hoses and lines: not chafed, kinked, cut or leaking. This is exactly where Brake Safety Week found hundreds of violations.
- Brake drums or rotors: no cracks, no contamination from oil or grease
- Springs, spring hangers, U-bolts, air bags and shock absorbers: nothing broken, shifted or missing
Step 8: Coupling system
The connection between tractor and trailer deserves its own stop.
- Fifth wheel securely mounted, no cracks, properly greased, locking jaws closed around the kingpin
- Release arm in the locked position
- No visible space between the upper and lower fifth wheel plates
- Glad hands sealed and connected with no audible leaks; air lines and the electrical cord not tangled, pinched or dragging
- Landing gear fully raised, handle secured
- Tug test: with the trailer brakes set, gently pull against the trailer in low gear to confirm the coupling holds
Step 9: Trailer: dry van
On a dry van:
- Doors close and latch properly; hinges and seals in good shape
- Seal number matches your paperwork when you are loaded
- Roof and side panels free of holes that could let water in
- Floor and cross members not broken (check inside when empty)
- Trailer tandem slider pins fully locked
- Mud flaps present
Step 10: Trailer: reefer
On a reefer, do everything on the dry van list, plus check the refrigeration unit:
- Reefer fuel level, separate from the tractor's tanks on most units
- Unit starts and runs without alarms; set point matches the load paperwork
- Mode (continuous or cycle) matches the shipper's instructions
- Pre-cool the trailer before loading when the shipper requires it
- Door seals tight and air chute not torn
Our guide to dry van vs reefer CDL jobs in Texas explains how the extra reefer work changes the job, and our reefer CDL driver jobs in Texas page covers the reefer side of hiring at Maas.
Step 11: Final walkaround and paperwork
- One last lap to make sure nothing was left open, loose or forgotten
- Note anything you found and report defects to dispatch before you roll
- Make sure your bills of lading, permits and registration are where they belong
Common pre-trip mistakes
- Rushing it. A pre-trip done in two minutes is a pre-trip that skips something.
- Changing the order. Do it the same way every day so your hands and eyes remember the next step.
- Skipping the air brake check because "it was fine yesterday."
- Trusting the last driver. Review the last DVIR, then check for yourself.
- Logging time you did not spend. Record your inspection honestly on your ELD. An inspection that shows zero minutes is a red flag to anyone who reviews it.
- Not speaking up. If something is wrong, tell dispatch. A good carrier would rather fix it now than send you down the road with it.
How a good pre-trip helps you get hired, and stay hired
When a carrier reviews a driver, safety history matters. Clean roadside inspections, few out-of-service violations and good habits are what recruiters and safety managers notice. Our CDL-A hiring checklist for Dallas–DFW walks through what to have ready when you apply, and our guide to vetting trucking companies in Dallas that are hiring helps you check the carrier back.
It works the other way, too. When you interview with a carrier, ask how it handles defects: how you report them, how fast the shop responds, and what happens if a truck is not right to roll. Ask about the equipment. Maas runs 2020–2025 Freightliner Cascadias with Samsara ELDs; see our fleet page.
If you are newer to the industry, our article on choosing your first carrier after CDL school in Texas explains why the habits you build in your first year stay with you. And if you are thinking about running OTR out of Dallas, read what an OTR dry van run out of Dallas looks like.
For owner-operators: your truck, your inspection, your money
If you own your truck, every defect is your cost and every out-of-service order is lost revenue. A disciplined pre-trip is cheap insurance against both. Build regular maintenance into your numbers; our guide to owner-operator cost per mile shows how to work out your break-even. Owner-operators leased to Maas keep 87–90% of gross with non-forced dispatch. Apply as an owner-operator.
Drive with Maas Logistics
Maas Logistics LLC runs dry van and reefer full truckload out of Melissa, Texas and the Dallas–Fort Worth area across the lower 48 states. Here is what we can tell you for certain:
- Asset-based carrier, founded in 2018, USDOT 3179194, Satisfactory safety rating
- Our own trucks: 2020–2025 Freightliner Cascadias with Samsara ELDs
- Company drivers: 50+ CPM dry van, 60+ CPM reefer, weekly direct deposit (1099)
- Owner-operators: 87–90% of gross, non-forced dispatch
- Drivers 23+ with 3 years of experience
- 24/7 dispatch at (916) 770-7323
Ready to talk? Apply as a company driver or apply as an owner-operator. More questions? See our driver FAQs. Shippers who need dry van trucking or refrigerated trucking out of DFW can request a truckload quote.
FAQ
What is on a CDL pre-trip inspection checklist?
At minimum, the items in 49 CFR 392.7: service brakes including trailer brake connections, parking brake, steering, lights and reflectors, tires, horn, windshield wipers, mirrors, coupling devices, wheels and rims, and emergency equipment. A full tractor-trailer pre-trip also covers the engine compartment, the air brake check, suspension, the trailer body and, on a reefer, the refrigeration unit.
How long should a pre-trip inspection take?
There is no fixed federal time. A thorough tractor-trailer pre-trip usually takes several minutes or more, depending on the equipment and what you find. What matters is that it is complete and that you record it honestly on your ELD.
What are the air brake check numbers for a combination vehicle?
Using the standard CDL manual figures for a dual air system: pressure builds from 85 to 100 psi within about 45 seconds; static leakage less than 3 psi in one minute; applied leakage no more than 4 psi in one minute after the initial drop; low-air warning before 60 psi; spring brakes apply between 20 and 45 psi. Always confirm with your state CDL handbook and the truck's manual.
What is the minimum tire tread depth for a semi truck?
Under 49 CFR 393.75, at least 4/32 of an inch on steer tires and at least 2/32 of an inch on all other tires, measured in a major tread groove.
Do I have to fill out a DVIR if nothing is wrong?
Under 49 CFR 396.11, drivers of property-carrying vehicles are not required to prepare a report if no defect or deficiency is discovered by or reported to them. If there is a defect, it must be reported and the carrier must repair it, or certify repair is unnecessary, before the vehicle runs again.
What extra checks does a reefer pre-trip need?
Check the reefer fuel level, that the unit starts and runs without alarms, that the set point and mode match the load paperwork, that the trailer is pre-cooled when required, and that door seals and the air chute are in good shape.
What does Maas Logistics need from drivers?
A valid Class A CDL, age 23 or older, at least 3 years of experience, and the ability to meet federal DOT requirements. Company drivers earn 50+ CPM dry van and 60+ CPM reefer; owner-operators keep 87–90% of gross with non-forced dispatch. Apply at https://maaslogistic.com/drive-with-us/company-drivers or https://maaslogistic.com/drive-with-us/owner-operators.
Sources for figuresand rules cited: 49 CFR 392.7, Equipment, inspection and use (https://www.ecfr.gov/current/title-49/subtitle-B/chapter-III/subchapter-B/part-392/subpart-A/section-392.7); 49 CFR 396.11, Driver vehicle inspection reports (https://www.ecfr.gov/current/title-49/subtitle-B/chapter-III/subchapter-B/part-396/section-396.11); 49 CFR 396.13, Driver inspection (https://www.ecfr.gov/current/title-49/subtitle-B/chapter-III/subchapter-B/part-396/section-396.13); 49 CFR 393.75, Tires (https://www.ecfr.gov/current/title-49/subtitle-B/chapter-III/subchapter-B/part-393/subpart-G/section-393.75); CVSA, "CVSA Releases 2026 Brake Safety Week Results" (Nov. 6, 2026, https://cvsa.org/news/cvsa-releases-2026-brake-safety-week-results); FreightWaves, "Big carriers keep FMCSA's crackdown alive, Fuller says" (Nov. 7, 2026, https://www.freightwaves.com/news/fuller-big-carriers-fmcsa-crackdown-permanent).